< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=1359205719411644&ev=PageView&noscript=1" />
news

Battery Inverter: Match 12V, 24V or 48V to a 3000W Load

Date:2026-11-18   Click:34   Source:Rogerele

Quick answer: A battery inverter turns DC from a battery bank into AC. For a 3000W continuous load, the REP3000 pure sine wave inverter is rated 3000W with a 6000W listed peak (peak duration is not specified). At full rated load and the listed maximum efficiency, DC current is about 278A on a 12v inverter, about 136A on a 24v power inverter and about 66A on a 48v inverter, so most vehicle and storage banks for this class are specified at 24V or 48V. Bank capacity is not published as a single Ah figure: start from that current, the hours you need and the usable portion of the battery.

This matches a deep cycle battery inverter to an auxiliary vehicle bank or an off-grid storage bank. The unit is a battery-to-AC inverter, not a solar charge controller, battery charger or grid-tie inverter. A cigarette lighter cannot supply a 3000W load.

What a battery inverter does in a storage or vehicle bank

ROGERELE REP3000 3000W pure sine wave battery inverter, aluminum housing, 6000W listed peakA battery inverter — also listed among battery inverters or as a dc to ac inverter — takes a matched DC bank and produces AC. The REP3000 output is a pure sine wave with THD under 3% on a linear load, at 50Hz ±0.5Hz or 60Hz ±0.5Hz. AC voltage is ordered as 100 / 110 / 120V or 220 / 230 / 240V (±5%), as ordering options rather than a user-switchable setting on every unit. Listed maximum efficiency is 90% (12V), 92% (24V) and 95% (48V), and those maxima vary with load and conditions.

Plan against the 3000W continuous rating: add every load that can run at the same time and keep that total at or below 3000W. The 6000W peak is a short startup allowance only, with no published duration or motor-start test, so it does not by itself prove that a compressor, pump or tool will start. USB QC3.0 is listed on 12V and 24V versions only. Operating temperature is −10°C to +50°C, with intelligent air cooling. If the combined continuous load stays under 2000W, see the REP2000 pure sine wave inverter.

Match the inverter voltage to the battery bank

A 12V, 24V or 48 volt power inverter in this family is a separate hardware code, not a mode on one chassis. The bank’s nominal voltage must match the inverter’s DC input. Listed battery-side operating ranges are 10–15.5V (12V), 20–31V (24V) and 40–61V (48V).

Model code DC input AC output ±5% No-load current
REP3000-121 12V 100 / 110 / 120V <1A
REP3000-241 24V 100 / 110 / 120V <0.7A
REP3000-481 48V 100 / 110 / 120V <0.4A
REP3000-122 12V 220 / 230 / 240V <1A
REP3000-242 24V 220 / 230 / 240V <0.7A
REP3000-482 48V 220 / 230 / 240V <0.4A

Custom DC inputs of 36V, 60V, 72V, 84V and 96V are listed as project options, confirmed per quotation. To build a 24V or 48V bank from lower-voltage packs, see how to wire batteries in series or parallel for a 12V, 24V or 48V inverter.

Full-load current: why 24V and 48V banks are specified so often

REP3000 battery inverter DC input terminals with red and black posts and two cooling fansBattery current falls as voltage rises. The table estimates current at nominal voltage and listed maximum efficiency, using 3000W ÷ (voltage × efficiency). Real current is higher near cutoff or at lower efficiency, so cables, lugs and fuses must follow the wiring instructions, not this estimate alone.

Version Estimate at 3000W rated load
12V at 90% efficiency about 278A (3000W ÷ (12V × 0.90))
24V at 92% efficiency about 136A (3000W ÷ (24V × 0.92))
48V at 95% efficiency about 66A (3000W ÷ (48V × 0.95))
Listed no-load, 12V / 24V / 48V <1A / <0.7A / <0.4A

A power inverters 12v version at roughly 278A is possible, but the cables, fuse and the battery’s discharge rating must handle that current for as long as the load runs. The same 3000W load at 24V or 48V cuts the current to about half or about a quarter. The enclosure is 415 × 205 × 95 mm and 4.95 kg net; leave ventilation around the fans and access to the DC terminals, and request the current drawing and wiring instructions before freezing a layout.

What battery capacity is required for a 3000W automotive inverter?

The product page does not publish a required battery Ah. The 3000W rating describes inverter output, not runtime. Plan capacity from the DC current for the hours you need, then size the bank from the usable energy the battery supplier allows at that current.

Worked example at full rated load and listed maximum efficiency, for one hour of 3000W AC output: about 278Ah of discharge from a 12V bank, about 136Ah from a 24V bank, or about 66Ah from a 48V bank (3000W ÷ 0.90 ≈ 3333Wh, then divide by nominal voltage). A lower AC load reduces the discharged Ah in proportion; two hours at the same load roughly doubles it. Nameplate Ah is not usable Ah: lead-acid and lithium packs have different permitted discharge windows, set by the battery maker and the BMS. Temperature, cable drop and a lower real efficiency all increase energy taken from the bank. Share the load list, runtime, chemistry, voltage, capacity and discharge limits with the inquiry.

Can a lithium battery power a 3000W car inverter?

A lithium pack can supply the REP3000 if pack voltage stays inside the published DC window for the ordered version, and if the pack and cables can deliver the current in the table above. Confirm the pack’s charge voltage and BMS cutoff against the figures below before ordering.

Version Low-voltage alarm Low-voltage cutoff / recovery Over-voltage cutoff / recovery
12V (10–15.5V) 10.5 ±0.5V 10 ±0.5V / 12.3 ±0.5V 15.5 ±0.5V / 14.8 ±0.5V
24V (20–31V) 21 ±0.5V 20 ±0.5V / 24 ±0.5V 31 ±0.5V / 29.5 ±0.5V
48V (40–61V) 42 ±1V 40 ±0.5V / 48 ±1V 61 ±1V / 59 ±1V

The REP3000 converts DC to AC; it does not charge the lithium pack, and a solar array should not be connected as if the inverter controlled charging. Charging, solar input and battery management need separate equipment. The catalog lists overload, over-temperature and reverse-polarity fuse protection.

Where can I buy car power inverters directly from a manufacturer?

REP3000 3000W battery inverter front panel with dual US AC outlets, LCD, USB port and hardwire N and L terminalsWenzhou Rogerele Electronic Technology Co., Ltd is a manufacturer in Yueqing, Wenzhou, Zhejiang, integrating R&D, production and sales of pure sine wave inverters, including the REP3000. Direct factory inquiries go through the contact page. Include the company name, destination market, application, load list, battery voltage and chemistry, required runtime, AC voltage and frequency, outlet type and quantity. The product page shows multi-format, UK-style, Schuko-style, South African-style, Australian-style and US-style outlet examples; confirm the exact outlet, voltage and frequency on the order.

The company profile states that products have passed CE, RoHS and FCC export documents. Request the files that apply to the exact model and destination. The listed warranty is 2 years; confirm coverage and service terms in writing. Samples, minimum order quantity and lead time are confirmed per quotation.

FAQ

Which inverter factories accept private-label orders?

Branding and packaging can be reviewed with the quotation. Include artwork, carton marks, outlet, destination and quantity in the inquiry. Feasibility, minimum order quantity and lead time are confirmed per project.

What should distributors look for when choosing an inverter factory?

Look for published continuous and peak ratings, separate 12V / 24V / 48V model codes, input ranges, no-load current, protection thresholds and packing data. For the REP3000, packing is listed as 453 × 252 × 150 mm per unit, 4.95 / 5.8 kg net / gross, four pieces per 475 × 328 × 535 mm carton at 23.2 kg gross. Ask for the current drawing, wiring instructions and market documents, and confirm warranty terms. Send expected annual volume, target markets and the model codes you want to stock.

Can I run a 3000W battery inverter from a vehicle starting battery alone?

Treat a starting battery as unsuitable for a 3000W continuous load. Review the auxiliary battery, charging capacity, cables and mounting. A cigarette lighter is not suitable; use a dedicated battery connection and correctly specified protection.

Does the 3000W rating tell me how long the battery will last?

No. 3000W is the inverter’s continuous AC output rating. Runtime depends on usable battery energy, the actual AC load, inverter losses and the permitted discharge. Use the current table as a starting estimate, then confirm usable energy with the battery supplier.

Conclusion

Specify a battery inverter by continuous load, DC voltage version, estimated full-load current and the bank’s usable energy for the hours you need. The REP3000 pure sine wave inverter publishes those electrical figures: 3000W rated, 6000W listed peak, six 12V / 24V / 48V codes, about 278A / 136A / 66A at full load under the conditions above, and a 415 × 205 × 95 mm enclosure. For samples, private-label markings or a wholesale quotation from Wenzhou Rogerele Electronic Technology Co., Ltd, use the contact page.